Original Article
  • Residual Stress Comparison of Type III Hydrogen Tank by Curing Conditions

  • Yong-Chul Shin*†

  • Department of Mechanical and Aerospace Engineering, Seoul National University, Korea

  • Type III 수소탱크 경화조건에 따른 잔류응력 비교

  • 신용철*†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Lee, K.H., Koo, K.M., Ryu, C.H., and Hwang, G.J., “Study on Cooling of Hydrogen Gas for the Pre-cooler in the Hydrogen Refueling Station”, Trans. of Korean Hydrogen and New Energy Society, Vol. 30, No. 3, 2019, pp. 237-242.
  •  
  • 2. Park, B.H., “Calculation and Comparison of Thermodynamic Properties of Hydrogen Using Equations of State for Compressed Hydrogen Storage”, Trans. of Korean Hydrogen and New Energy Society, Vol. 31, No. 2, 2020, pp. 184-193.
  •  
  • 3. Hwang, S.I., Kang, S.K., and Huh, Y.S., “A Study on the Safety Improvement by CFD Analysis for Packaged Type Hydrogen Refueling System”, Trans. of Korean Hydrogen and New Energy Society, Vol. 30, No. 3, 2019, pp. 243-250.
  •  
  • 4. Park, B.H., “Simulation of Temperature Behavior in Hydrogen Tank during Refueling Using Cubic Equations of State”, Trans. of Korean Hydrogen and New Energy Society, Vol. 30, No. 5, 2019, pp. 385-394.
  •  
  • 5. Zheng, J., Guo, J., Yang, J., Zhao, Y., Zhao, L., Pan, X., Ma, J., and Zhang, L., “Experimental and Numerical Study on Temperature Rise within a 70 MPa Type III Cylinder During Fast Refueling”, International Journal of Hydrogen Energy, Vol. 38, No. 25, 2013, pp. 10956-10962.
  •  
  • 6. Alam, M.M.A., Setoguchi, T., and Matsuo, S., “An Attempt of Simulating the Real Time Filling of H2 Cylinder at 70MPa”, OTEC, Vol. 19, 2014, pp. 27-32.
  •  
  • 7. Suryan, A., Kim, H.D., and Setoguchi, T., “Three Dimensional Numerical Computations on the Fast Filling of a Hydrogen Tank under Different Conditions”, International Journal of Hydrogen Energy, Vol. 37, No. 9, 2012, pp. 7600-7611.
  •  
  • 8. Zheng, J., Guo, J., Yang, J., Zhao, Y., Zhao, L., Pan, X., Ma, J., and Zhang, L., “Experimental and Numerical Study on Temperature Rise within a 70 MPa Type III Cylinder During Fast Refueling”, International Journal of Hydrogen Energy, Vol. 38, No. 25, 2013, pp. 10956-10962.
  •  
  • 9. Wu, X., Liu, J., Shao, J., and Deng, G., “Fast Filling Strategy of Type III On-board Hydrogen Tank Based on Time-delayed Method”, International Journal of Hydrogen Energy, Vol. 46, Issue 57, 2021, pp. 29288-29296.
  •  
  • 10. Li, B., Han, B., Li, Q., Gao, W., Guo, C., Lv, H., Liu, Y., Jin, X., and Bi, M., “Study on Hazards from High-pressure On-board Type III Hydrogen Tank in Fire Scenario: Consequences and Response Behaviours”, International Journal of Hydrogen Energy, Vol. 47, Issue 4, 2022, pp. 2759-2770.
  •  
  • 11. Reddi, K., Elgowainy, A., Rustagi, N., and Gupta, E., “Impact of Hydrogen SAE J2601 Fueling Methods on Fueling Time of Light-duty Fuel Cell Electric Vehicles”, International Journal of Hydrogen Energy, Vol. 42, No. 26, 2017, pp. 16675-16685.
  •  
  • 12. Xiao, J., Wang, X., Benard, P., and Chahine, R., “Determining Hydrogen Pre-cooling Temperature from Refueling Parameters”, International Journal of Hydrogen Energy, Vol. 41, No. 36, 2016, pp. 16316-16321.
  •  
  • 13. Tomioka, J-I., Kiguchi, K., Tamura, Y., and Mitsuishi, H., “Influence of Pressure and Temperature on the Fatigue Strength of Type-3 Compressed-hydrogen Tanks”, International Journal of Hydrogen Energy, Vol. 37, No. 22, 2012, pp. 17639-17644.
  •  
  • 14. Guo, J., Yang, J., Zhao, Y., Pan, X., Zhang, L., Zhao, L., et al. “Investigations on Temperature Variation within a type III Cylinder during the Hydrogen Gas Cycling Test”, International Journal of Hydrogen Energy, Vol. 39, No. 25, 2014, pp. 13926-13934.
  •  
  • 15. Tomioka, J-I., Kiguchi, K., Tamura, Y., and Mitsuishi, H., “Influence of Temperature on the Fatigue Strength of Compressed Hydrogen Tanks for Vehicles” International Journal of Hydrogen Energy, Vol. 36, No. 3, 2011, pp. 2513-2519.
  •  
  • 16. Zhao, L., Liu, Y., Yang, J., Zhao, Y., Zheng, J., Bie, H., et al. “Numerical Simulation of Temperature Rise Within Hydrogen Vehicle Cylinder during Refueling”, International Journal of Hydrogen Energy, Vol. 35, No. 15, 2010, pp. 8092-8100.
  •  
  • 17. Lee, S., and Springer, G., “Filament Winding Cylinders: I. Process Model”, Journal of Composite Materials, Vol. 24, Issue 12, 1990, pp. 1270-1298.
  •  
  • 18. Calius, E., Lee, S., and Springer, G., “Filament Winding Cylinders: II. Validation of the Process Model”, Journal of Composite Materials, Vol. 24, Issue 12, 1990, pp. 1299-1343.
  •  
  • 19. Lee, S., and Springer, G., “Filament Winding Cylinders: I. Process Model”, Journal of Composite Materials, Vol. 24, Issue 12, 1990, pp. 1344-1366.
  •  

This Article

Correspondence to

  • Yong-Chul Shin

  • Department of Mechanical and Aerospace Engineering, Seoul National University, Korea

  • E-mail: yongchulnim@snu.ac.kr