Original Article
  • A Study on the Strength Characteristics and Failure Detection of Single-lap Joints with I-fiber Stitching Method

  • Seong-Hyun Choi*, Sang-Hoon Song*, Woo-Jin An*, Jin-Ho Choi*†

  • * Research Center for Aircraft Parts Technology, School of Mechanical and Aerospace Engineering, Gyeongsang National University

  • I-fiber 스티칭 공법이 적용된 Single-lap Joint의 강도 특성 및 파손 신호 검출 연구

  • 최성현* · 송상훈* · 안우진* · 최진호*†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Plain, K.P., and Tong, L., “The Effect of Stitch Incline Angle on Mode I Fracture Toughness – Experimental and Modelling,” Composite Structures, Vol. 92, No. 7, 2010, pp. 1620-1630.
  •  
  • 2. Aymerich, F., “Effect of Stitching on the Static and Fatigue Performance of Co-cured Composite Single-lap Joints,” Journal Composite Materials, Vol. 38, No. 3, 2004, pp. 243-257.
  •  
  • 3. Beylergil, B., Cunedioglu, Y., and Aktas, A., “Experimental and Numerical Analysis of Single Lap Composite Joints with Inter-adherend Fibers,” Composites: Part B, Vol. 42, No. 7, 2011, pp. 1885-1896.
  •  
  • 4. Mouritz, A.P., and Cox, B.N., “A Mechanistic Approach to the Properties of Stitched Laminates,” Composites Part A: Applied Science and Manufacturing, Vol. 31, No. 1, 2000, pp. 1-27.
  •  
  • 5. Ji, H., Kweon, J.H., and Choi, J.H., “Fatigue Characteristics of Stainless Steel Pin-reinforced Composite Hat Joints”, Composite Structures, Vol. 108, 2014, pp. 49-56.
  •  
  • 6. Chang, P., Mouritz, A.P., and Cox, B.N., “Properties and Failure Mechanisms of Pinned Composite Lap Joints in Monotonic and Cyclic Tension,” Composites Science and Technology, Vol. 66, No. 13, 2006, pp. 2163-2176.
  •  
  • 7. Steeves, C.A., and Fleck, N.A., “In-plane Properties of Composite Laminates with Through-thickness Pin Reinforcement,” International Journal of Solids and Structures, Vol. 43, No. 10, 2006, pp. 3197-3212.
  •  
  • 8. Song, S.-H., Back, J.-T., An, W.-J., and Choi, J.-H., “Static Strength of Composite Single-lap Joints Using I-fiber Stitching Process with different Stitching Pattern and Angle,” Composites Research, Vol. 33, No. 5, 2020, pp. 296-301.
  •  
  • 9. Kim, C.H., Jo, D.H., and Choi, J.H., “Failure Strength of Composite T-joints Prepared Using Anew 1-thread Stitching Process,” Composite Structures, Vol. 178, 2017, pp. 225-231.
  •  
  • 10. An, W.-J., Kim, C.-H., Choi, J.-H., and Kweon, J.-H., “Static Strength of RTM Composite Joint with I-fiber Stitching Process,” Composite Structures, Vol. 210, 2019, pp. 348-353.
  •  
  • 11. Kim, C.H., Sim, H.-W., An, W.-J., Kweon, J.-H., and Choi, J.-H., “Impact Characteristics of Composite Panel Stitched by I-fiber Process,” Composites Part A, Vol. 127, 2019, 105644.
  •  
  • 12. Kang, M.H., Choi, J.H., and Kweon, J.H., “Fatigue Life Evaluation and Crack Detection of the Adhesive Joint with Carbon Nanotubes,” Composite Structures, Vol. 108, 2014, pp. 417-422.
  •  
  • 13. Baek, S.J., Kim, M.S., An, W.J., and Choi, J.H., “Defect Detection of Composite Adhesive Joints Using Electrical Resistance Method”, Composite Structures, Vol. 220, 2019, pp. 179-184.
  •  
  • 14. Kim, C.H., Choi, J.H., and Kweon, J.H., “Composite Fracture Detection Capabilities of FBG Sensor and AE Sensor,” Composites Research, Vol. 27, No. 4, 2014, pp. 152-157.
  •  

This Article

Correspondence to

  • Jin-Ho Choi

  • Research Center for Aircraft Parts Technology, School of Mechanical and Aerospace Engineering, Gyeongsang National University

  • E-mail: choi@gnu.ac.kr