Jung Hyuk Jang*, Yi Je Cho*†
* Department of Materials Science and Engineering, Sunchon National University, Suncheon 57922, Republic of Korea
장정혁* · 조의제*†
This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
The mechanical behaviors and reinforcement mechanism of shape memory CZ particle-reinforced Al composites were investigated using three-dimensional representative volume element (RVE) models generated by random sequential adsorption and relaxation algorithms. The appropriate RVE size was determined to be 4 mm based on comparison of the predicted mechanical properties with analytical models. Under compression, load-aligned particles carried higher stresses, whereas plastic strain localized in the intervening Al matrix, forming preferential load-transfer paths. Heating after unloading reduced particle stress and composite strain through reverse transformation of the CZ particles, but matrix plasticity and thermal residual stresses limited recovery. Increasing particle volume fraction from 20 to 30 vol% enhanced load transfer, yield strength, and recovery, while smaller particles distributed loads more uniformly, increasing work hardening and recovery. Neck-fractured and polygonal particles carried greater loads than spherical particles but intensified local matrix deformation through stress concentrations at necks and corners. Thus, optimizing CZ/Al composites requires balancing particle load transfer against matrix plasticity and morphology-dependent stress concentration.
Random sequential adsorption 알고리즘과 relaxation 기법을 접목하여 생성한 3차원 RVE (representative volume element) 모델을 사용하여 형상기억 CZ 입자 강화 Al 복합재료의 기계적 거동과 강화 메커니즘을 조사하였다. 예측된 기계적 특성을 분석적 모델의 계산 결과와 비교하여, 적합한 RVE 모델의 한 변의 길이를 4 μm로 선정하였다. 압축 변형 중 하중 방향으로 배열된 입자에는 높은 응력이 형성되었으며, 입자 사이의 좁은 Al 기지 영역에는 소성 변형이 집중되어 국부적인 하중 전달 경로가 형성되었다. 하중 제거 후 가열 중 CZ 입자의 역변태에 의해 입자의 응력과 복합재료의 변형률이 감소하였으나, 기지의 소성 변형과 열적 잔류 응력으로 인해 회복이 제한되었다. 입자 부피 분율이 20 vol%에서 30 vol%로 증가함에 따라 입자의 하중 분담, 항복강도 및 회복률이 증가하였다. 또한, 입자 크기가 감소할수록 하중이 더 균일하게 분산되어 가공경화율과 회복률이 증가하고 기지의 국부적인 소성 변형이 억제되었다. Neck-fractured 및 polygonal 입자는 구형 입자보다 높은 하중 분담을 나타냈으나, neck 영역과 모서리에서의 응력 집중으로 인접 Al 기지의 국부적인 소성 변형이 증가하였다. 따라서 CZ 입자 강화 Al 복합재료의 미세조직 설계에서는 입자의 하중 전달과 기지의 소성 변형 및 입자 형상에 따른 응력 집중의 균형을 고려해야 한다.
Keywords: 세리아-지르코니아 입자(Ceria-zirconia particle), 알루미늄 복합재료(Aluminum composite), 형상 기억 효과(Shape memory effect), 미세조직 모델링(Microstructure modeling), 기계적 거동(Mechanical behavior)
This Article2026; 39(5): 433-443
Published on Oct 31, 2026
Correspondence toDepartment of Materials Science and Engineering, Sunchon National University, Suncheon 57922, Republic of Korea