Original Article
  • Structural Analysis and Strength Evaluation of an L-Shaped Sandwich Composite Joint for a Rotor Sail
  • Min-Seong Hwang*, Min-Jung Jun**, Seung-Un Yang***, Byeong-Hun Min*, Jin-Ho Choi*†

  • * DTCI, School of Mechanical and Aerospace Engineering, Gyeongsang National University
    ** Hanwha Ocean Co., Ltd.
    *** Human Composites Co., Ltd

  • 로터세일 L형 샌드위치 복합재 조인트의 구조해석 및 강도평가
  • 황민성* · 전민정** · 양승운*** · 민병훈* · 최진호*†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Birman, V., and Kardomateas, G.A., “Review of Current Trends in Research and Applications of Sandwich Structures,” Composites Part B: Engineering, Vol. 142, 2018, pp. 221-240.
  •  
  • 2. Shen, W., Luo, B., Yan, R., Zeng, H., and Xu, L., “The Mechanical Behavior of Sandwich Composite Joints for Ship Structures,” Ocean Engineering, Vol. 144, 2017, pp. 78-89.
  •  
  • 3. Zeng, H., Yan, R., and Xu, L., “Failure Prediction of Composite Sandwich L-Joint under Bending,” Composite Structures, Vol. 197, 2018, pp. 54-62.
  •  
  • 4. Li, H., Tu, S., Liu, Y., Lu, X., and Zhu, X., “Mechanical Properties of L-Joint with Composite Sandwich Structure,” Composite Structures, Vol. 217, 2019, pp. 165-174.
  •  
  • 5. Qin, K., Yan, R., Cui, M., and Zeng, H., “Failure Mode Shift of Sandwich Composite L-Joint for Ship Structures under Tension Load,” Ocean Engineering, Vol. 214, 2020, 107863.
  •  
  • 6. Li, M., Liu, Z., Yan, R., Lu, J., and Guedes Soares, C., “Experimental and Numerical Investigation on Composite Single-Lap Single-Bolt Sandwich Joints with Different Geometric Parameters,” Marine Structures, Vol. 85, 2022, 103259.
  •  
  • 7. Feih, S., and Shercliff, H.R., “Adhesive and Composite Failure Prediction of Single-L Joint Structures under Tensile Loading,” International Journal of Adhesion and Adhesives, Vol. 25, No. 1, 2005, pp. 47-59.
  •  
  • 8. Wei, Y., Jin, X., Luo, Q., Li, Q., and Sun, G., “Adhesively Bonded Joints—A Review on Design, Manufacturing, Experiments, Modeling and Challenges,” Composites Part B: Engineering, Vol. 276, 2024, 111225.
  •  
  • 9. Katnam, K.B., Stevenson, J.P.J., Stanley, W.F., Buggy, M., and Young, T.M., “Tensile Strength of Two-Part Epoxy Paste Adhesives: Influence of Mixing Technique and Micro-Void Formation,” International Journal of Adhesion and Adhesives, Vol. 31, No. 7, 2011, pp. 666-673.
  •  
  • 10. Akhavan-Safar, A., Ayatollahi, M.R., and da Silva, L.F.M., “Strength Prediction of Adhesively Bonded Single Lap Joints with Different Bondline Thicknesses: A Critical Longitudinal Strain Approach,” International Journal of Solids and Structures, Vol. 109, 2017, pp. 189-198.
  •  
  • 11. Afendi, M., Teramoto, T., and Bakri, H.B., “Strength Prediction of Epoxy Adhesively Bonded Scarf Joints of Dissimilar Adherends,” International Journal of Adhesion and Adhesives, Vol. 31, No. 6, 2011, pp. 402-411.
  •  
  • 12. Harris, J.A., and Adams, R.D., “Strength Prediction of Bonded Single Lap Joints by Non-linear Finite Element Methods,” International Journal of Adhesion and Adhesives, Vol. 4, No. 2, 1984, pp. 65-78.
  •  
  • 13. Adams, R.D., and Mallick, V., “The Effect of Temperature on the Strength of Adhesively-Bonded Composite-Aluminium Joints,” The Journal of Adhesion, Vol. 43, No. 1-2, 1993, pp. 17-33.
  •  
  • 14. Rodríguez, R.Q., de Paiva, W.P., Sollero, P., Rodrigues, M.R.B., and de Albuquerque, E.L., “Failure Criteria for Adhesively Bonded Joints,” International Journal of Adhesion and Adhesives, Vol. 37, 2012, pp. 26-36.
  •  
  • 15. McCarthy, C.T., McCarthy, M.A., Stanley, W.F., and Lawlor, V.P., “Experiences with Modeling Friction in Composite Bolted Joints,” Journal of Composite Materials, Vol. 39, No. 21, 2005, pp. 1881-1908.
  •  
  • 16. Liu, L., Zhang, X., Wang, Z., Wang, Y., and Guo, J., “Micromechanics Modeling of Transverse Tensile Strength for Unidirectional CFRP Composite,” Materials, Vol. 15, No. 23, 2022, 8577.
  •  
  • 17. Hwang, M.S., “A Study on the Structural Optimization of Composite Rotor Sail L-Flange Joints Based on Experimental Testing and Finite Element Analysis,” M.S. Thesis, Gyeongsang National University, Jinju, Korea, 2026.
  •  

This Article

Correspondence to

  • Jin-Ho Choi
  • DTCI, School of Mechanical and Aerospace Engineering, Gyeongsang National University

  • E-mail: choi@gnu.ac.kr