Original Article
  • Analysis of Mechanical Properties and Lightweight Efficiency of LW-PLA for Solid Propellant Rocket Fuselage Application

  • U-Daam Choi*, Jaehyun Seo*, Jane Byun*, Mingeon Choi*, Dayeon Choi*, Dowon Choi**, Kyungwho Choi*†

  • *School of Mechanical Engineering, Sungkyunkwan University
    **School of Advanced Materials Science & Engineering, Sungkyunkwan University

  • 고체 추진 모형 로켓 동체 적용을 위한 LW-PLA의 기계적 특성 및 경량화 효율 분석

  • 최유담* · 서재현* · 변재인* · 최민건* · 최다연* · 최도원** · 최경후*†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Krishnan, Anish B., and Thakur, Dineshsingh G., “Impact of Solid Rocket Propellant Grain Manufacturing Limitations on Launch Vehicle Capability,” Defence Science Journal, 2024, Vol. 74. DOI: 10.14429/dsj.74.19792.
  •  
  • 2. Koo, K.R., Kim, H.G., Kim, D.G., Kwon, S.C., and Oh, H.U., “Lightweight Design for Active Small SAR S-STEP Satellite Using Multilayered High-Damping Carbon Fiber-Reinforced Plastic Patch”, Aerospace, 2023, Vol. 10, No. 9, p. 774. DOI: 10.3390/aerospace10090774.
  •  
  • 3. Rhee, S.Y., Kim, K., Yoon, Y.H., Yi, M.K., and Kim, H.C., “Test Evaluation of a Linerless Composite Propellant Tank Using the Composite Collapsible Mandrel,” Composites Research, 2023, Vol. 36, No. 2, pp. 132-139. DOI: 10.7234/composres.2023.36.2.132.
  •  
  • 4. Mahjub, A., Mazlan, N.M., Abdullah, M.Z., and Azam, Q., “Design Optimization of Solid Rocket Propulsion: A Survey of Recent Advancements,” Journal of Spacecraft and Rockets, 2020, Vol. 57, No. 1, pp. 3-11. DOI: 10.2514/1.A34594.
  •  
  • 5. Wang, G., Liu, K., Sun, Z., and Li, Y., “Multistage Liquid Rocket Weight Estimation and Optimization for Early Design Stages,” Journal of Aerospace Engineering, 2020, Vol. 33, No. 6, p. 04020081. DOI: 10.1061/(ASCE)AS.1943-5525.0001181.
  •  
  • 6. Hueber, C., Horejsi, K., and Schledjewski, R., “Review of Cost Estimation: Methods and Models for Aerospace Composite Manufacturing,” Advanced Manufacturing: Polymer & Composites Science, 2016, Vol. 2, No. 1, pp. 1-13. DOI: 10.1080/20550340. 2016.1154642.
  •  
  • 7. Witik, R.A., Teuscher, R., Michaud, V., Ludwig, C., and Månson, J.A.E., “Carbon Fibre Reinforced Composite Waste: An Environmental Assessment of Recycling, Energy Recovery and Landfilling,” Composites Part A: Applied Science and Manufacturing, 2013, Vol. 49, pp. 89-99. DOI: 10.1016/j.compositesa.2013.02.009.
  •  
  • 8. Ngo, T.D., Kashani, A., Imbalzano, G., Nguyen, K.T., and Hui, D., “Additive Manufacturing (3D printing): A Review of Materials, Methods, Applications and Challenges,” Composites Part B: Engineering, 2018, Vol. 143, pp. 172-196. DOI: 10.1016/j.compositesb.2018.02.012.
  •  
  • 9. Alami, A.H., Olabi, A.G., Alashkar, A., Alasad, S., Aljaghoub, H., Rezk, H., and Abdelkareem, M.A., “Additive Manufacturing in the Aerospace and Automotive Industries: Recent Trends and Role in Achieving Sustainable Development Goals”, Ain Shams Engineering Journal, 2023, Vol. 14, No. 11, p. 102516. DOI: 10.1016/j.asej.2023.102516.
  •  
  • 10. Penumakala, P.K., and Santo, J., and Thomas, A., “A Critical Review on the Fused Deposition Modeling of Thermoplastic Polymer Composites,” Composites Part B: Engineering, 2020, Vol. 201, p. 108336. DOI: 10.1016/j.compositesb.2020.108336.
  •  
  • 11. Popescu, D., Zapciu, A., Amza, C., Baciu, F., and Marinescu, R., “FDM Process Parameters Influence over the Mechanical Properties of Polymer Specimens: A Review,” Polymer Testing, 2018, Vol. 69, pp. 157-166. DOI: 10.1016/j.polymertesting.2018.05.020.
  •  
  • 12. Lee, J.H., Choi, U.-D., Choi, K., and Choi, D., “Research on Fabrication of CNT-based Thermoelectric Filament and Optimization of 3D Printing,” Composites Research, 2025, Vol. 38, No. 5, pp. 575-581. DOI: 10.7234/composres.2025.38.5.575.
  •  
  • 13. Yousefi Kanani, A., Rennie, A.EW., and Rahim, S.Z.B., “Additively Manufactured Foamed Polylactic Acid for Lightweight Structures,” Rapid Prototyping Journal, 2023, Vol. 29, No. 1, pp. 50-66. DOI: 10.1108/RPJ-03-2022-0100.
  •  
  • 14. Wang, S., Ma, Y., Deng, Z., Zhang, S., and Cai, J., “Effects of Fused Deposition Modeling Process Parameters on Tensile, Dynamic Mechanical Properties of 3D Printed Polylactic Acid Materials”, Polymer Testing, 2020, Vol. 86, p. 106483. DOI: 10.1016/j.polymertesting.2020.106483.
  •  
  • 15. Goh, G.D., Agarwala, S., Goh, G.L., Dikshit, V., Sing, S.L., and Yeong, W.Y., “Additive Manufacturing in Unmanned Aerial Vehicles (UAVs): Challenges and Potential,” Aerospace Science and Technology, 2017, Vol. 63, pp. 140-151. DOI: 10.1016/j.ast.2016.12.019.
  •  
  • 16. Blakey-Milner, B., Gradl, P., Snedden, G., Brooks, M., Pitot, J., Lopez, E., Leary, M., Berto, F., and Du Plessis, A., “Metal Additive Manufacturing in Aerospace: A Review,” Materials & Design, 2021, Vol. 209, p. 110008. DOI: 10.1016/j.matdes.2021.110008.
  •  
  • 17. Boschetto, A., Bottini, L., Macera, L., and Vatanparast, S., “Additive Manufacturing for Lightweighting Satellite Platform,” Applied Sciences, 2023, Vol. 13, No. 5, p. 2809. DOI: 10.3390/app13052809.
  •  
  • 18. Damanpack, A.R., Sousa, A., and Bodaghi, M., “Porous PLAs with Controllable Density by FDM 3D Printing and Chemical Foaming Agent,” Micromachines, 2021, Vol. 12, No. 8, p. 866. DOI: 10.3390/mi12080866.
  •  
  • 19. Park, Y.-E., and Lee, S., “Characterization of PLA/LW-PLA Composite Materials Manufactured by Dual-nozzle FDM 3D-Printing Processes,” Polymers, 2024, Vol. 16, No. 20, p. 2852. DOI: 10.3390/polym16202852.
  •  
  • 20. Griffiths, C.A., Rees, A., Morgan, A., and Korkees, F., “Optimisation of 3D Printing for Microcellular Polymers,” Polymers, 2023, Vol. 15, No. 19, p. 3910. DOI: 10.3390/polym15193910.
  •  
  • 21. Ozsoykal, I., and Yurt, A., “Introduction of a Novel Technique in Density-adjusted 3D Printing for the Manufacture of Soft-tissue-equivalent Radiological Phantoms,” Applied Sciences, 2024, Vol. 14, No. 2, p. 509. DOI: 10.3390/app14020509.
  •  
  • 22. Kalia, K., and Ameli, A., “Understanding the Process-microstructure-property Relationships in Material Extrusion Additive Manufacturing of Polylactic Acid Microcellular Foams,”Additive Manufacturing, 2023, Vol. 72, p. 103636. DOI: 10.1016/ j.addma.2023.103636.
  •  
  • 23. Alduais, A., and Özerinç, S., “Tunable Mechanical Properties of Thermoplastic Foams Produced by Additive Manufacturing,” eXPRESS Polymer Letters, 2023, Vol. 17, No. 3, pp. 317-333. DOI: 10.3144/expresspolymlett.2023.23.
  •  
  • 24. Nieto-peroy, C., and Emami, M.R., “CubeSat Mission: From Design to Operation,” Applied Sciences, 2019, Vol. 9, No. 15, p. 3110. DOI: 10.3390/app9153110.
  •  
  • 25. Šostakaitė, L., Šapranauskas, E., Rudinskas, D., Rimkus, A., and Gribniak, V., “Investigating Additive Manufacturing Possibilities for an Unmanned Aerial Vehicle with Polymeric Materials,” Polymers, 2024, Vol. 16, No. 18, p. 2600. DOI: 10.3390/polym16182600.
  •  
  • 26. Nistor, I., and Zaharia, S.M., “Integrated Approach to Design and Additive Manufacturing of Solar Unmanned Aerial Vehicles,” Applied Sciences, 2025, Vol. 15, No. 24, p. 12964. DOI: 10.3390/app152412964.
  •  
  • 27. Cuan-Urquizo, E., Barocio, E., Tejada-Ortigoza, V., Pipes, R.B., Rodriguez, C.A., and Roman-Flores, A., “Characterization of the Mechancal Properties of FFF Structures and Materials: A Review on the Experimental, Computational and Theoretical Approaches,” Materials, 2019, Vol. 12, No. 6, p. 895. DOI: 10.3390/ma12060895.
  •  
  • 28. Yousefi Kanani, A., and Kennedy, A., “Effect of the Material Extrusion Process Parameters on the Compressive Properties of Additively Manufactured Foamed and Nonfoamed Polylactic Acid Structures,” 3D Printing and Additive Manufacturing, 2024, Vol. 11, No. 1, pp. 207-218. DOI: 10.1089/3dp.2022.0091.
  •  
  • 29. Ferreira, R.T.L., Amatte, I.C., Dutra, T.A., and Bürger, D., “Experimental Characterization and Micrography of 3D Printed PLA and PLA Reinforced with Short Carbon Fibers,” Composites Part B: Engineering, 2017, Vol. 124, pp. 88-100. DOI: 10.1016/j.compositesb.2017.05.013.
  •  
  • 30. Phiri, R., Rangappa, S.M., Siengchin, S., Oladijo, O.P., and Ozbakkaloglu, T., “Advances in Lightweight Composite Structures and Manufacturing Technologies: A Comprehensive Review,” Heliyon, 2024, Vol. 10, No. 5, e39661. DOI: 10.1016/j.heliyon.2024.e39661.
  •  
  • 31. Ji, S.-I., Lim, Y.-H., and Kim, Y.-G., “Evaluation of Static Torque and Bending Characteristics of Power Transmission Shaft Using Carbon Fiber/Epoxy and Glass Fiber/Epoxy Composite Materials,” Composites Research, 2001, Vol. 14, No. 2, pp. 13-21.
  •  

This Article

Correspondence to

  • Kyungwho Choi

  • School of Mechanical Engineering, Sungkyunkwan University

  • E-mail: kw.choi@skku.edu