Original Article
  • A Study on Damage Detection of Fasteners Using Self-sensing of CFRP

  • Min Jong Lee*, Donghyeon Lee**, Yongseok Lee*, Ki-Eek Kwon****, Zuo-Jia Wang****, Woo-Seok Shim****, Mantae Kim***†, Dong-Jun Kwon *,**†

  • * School of Materials Science & Engineering Major in Polymer Engineering, Gyeongsang National University, Jinju, Korea
    ** Department of Materials Engineering and Convergence Technology, Research Institute for Green Energy Convergence Technology Gyeongsang National University, Jinju, Korea
    *** Aerospace Convergence Materials Center, Korea Institute of Ceramic Engineering and Technology, Jinju, Korea
    **** R&D Center, Dong Yang Piston Co., Ltd, Ansan 15420, Korea

  • CFRP의 자가 센싱을 이용한 패스너 손상 감지 연구

  • 이민종*·이동현**·이용석*·권기익****·왕작가****·심우석****·김만태***† ·권동준*,**†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Kim, H., “Effect of Filled Hole on Strength Behavior of CFRP Composites at Cold Temperature Dry and Elevated Temperature Wet,” Composites Reseach, Vol. 22, No. 3, 2009, pp. 82-88.
  •  
  • 2. Uz, M.E., Ozkat, E., Ersoy, M.C., and Salvan, N., “Examining the Effect of Threaded Bolt Fasteners on Steel Construction,” Scientific Reports, Vol. 14, No. 1, 2024, pp. 16355.
  •  
  • 3. Jung, I., Kim, J., Kim, E., Kim, C.D., Kim, N.R., Yang, C.M., Yu, W.R., Ahn, C.H., Jeon, S.Y., Cheon, J., and Na, W., “Enhanced Composite Laminate Fastening and Delamination Repair Using Hierarchical Thermoplastic Composite Rivets,” Composites Part B: Engineering, Vol. 277, 2024, pp. 111382.
  •  
  • 4. Zhang, J., Yang, T., Du, Y., He, R., and Liu, C., “Tensile Mechanical Properties and Damage Analysis of Layered Woven GFRP Composite Bolts,” Composites Part B: Engineering, Vol. 271, 2024, pp. 111155.
  •  
  • 5. Lee, D., Cho, G.I., Lim, H.M., Kim, M., and Kwon, D.J., “Investigation of Tensile Properties in Edge Modified Graphene Oxide(E-GO)/Epoxy Nano Composites,” Composites Research, Vol. 37, No. 3, 2024, pp. 209-214.
  •  
  • 6. Shahin, A., Cowled, C.J., Henri, B., and Fawzia, S., “Experimental Study on Shear Performance of Nail and Screw-laminated Timber-steel Composite and Timber-timber Systems Using Low-grade Timber and Mechanical Fasteners,” Construction and Building Materials, Vol. 418, 2024, pp. 135403.
  •  
  • 7. Dyson, C.J., Hopkins, W.A., Aljeran, D.A., Fox, M.F., and Priest, M., “Tribological Considerations of Threaded Fastener Friction and the Importance of Lubrication,” Tribology International, Vol. 191, 2024, pp. 109162.
  •  
  • 8. Shah, S.Z.H., Megat‐Yusoff, P.S.M., Sharif, T., Sajid, Z., Hussnain, S.M., and Choudhry, R.S., “Bearing Performance and Damage Characteristics of Rein‐infused Thermoplastic 3D Woven Composites Bolted Joints,” Polymer Composites, Vol. 45, No. 1, 2024, pp. 631-652.
  •  
  • 9. Yang, Y., Ma, Y., Liu, Z., Bao, Y., Wang, J., and Chen, C., “Analytical Method for Assembly-induced Deformation Prediction of Composite Bolted Joints with Assembly Gap,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 238, 2024, pp. 1212-1221.
  •  
  • 10. Lee, M.K., Cho, S., and Kim, M.O., “Experimental Study on the Adhesion and Performance Evaluation of Joints for Modified Polyethylene Coated Steel Pipes,” Composites Research, Vol. 37, No. 3, 2024, pp. 238-245.
  •  
  • 11. Hwang, D.W., Kumar, S., Ha, D.H., Jo, S.M., and Kim, Y.H., “Investigation of Tensile Behaviors in Open Hole and Bolt Joint Configurations of Carbon Fiber/Epoxy Composites,” Composites Research, Vol. 36, No. 4, 2023, pp. 259-263.
  •  
  • 12. Kim, Y.J., Ahn K.S, Choe, J., Lim, J., and Choi, S.W., “Mechanical Performance Study of Piggy Back Clamp for Submarine Cables,” Composites Research, Vol. 37, 2024, pp. 108-114.
  •  
  • 13. Bae, K.M., Yim, Y.J., Yoo, S.W., Ha, J.R., and Cho, J.H., “A Study on the Application of Composites to Pipe Support Clamps for the Light-weight LNGC,” Composites Research, Vol. 34, No. 1, 2021, pp. 8-15.
  •  
  • 14. Kim, S.K., and Kwon, J.H., “Strength Analysis of Composite Double-lap Bolted Joints by Progressive Failure Theory Based on Damage Variables,” Composites Research, Vol. 26, 2013, pp. 91-98.
  •  
  • 15. Park, S.J., Ko, M.G., Kim, D.G., Kim, S.K., Moon, C.O., and Kwon, J.H., “Design and Verification of Shear Buckling Test Fixture for Composite Laminate,” Composites Research, Vol. 27, No. 4, 2014, pp. 158-167.
  •  
  • 16. Wei, Y., Jin, X., Luo, Q., Li, Q., and Sun, G., “Adhesively Bonded Joints–a Review on Design, Manufacturing, Experiments, Modeling and Challenges,” Composites Part B: Engineering, Vol. 276, No. 1, 2024, pp. 111225.
  •  
  • 17. Jing, G., Hu, C., Qin, Y., Sun, X., and Ma, T., “Complex Mechanisms of PEMFC Performance Variations Influenced by Both Structural Deformation and Contact Resistance under the Clamping Force,” International Journal of Hydrogen Energy, Vol. 58, 2024, pp. 137-148.
  •  
  • 18. Mazzeo, F., and Di Ilio, G., “Fuel Cell Hybrid Electric Propulsion System for a Lightweight Helicopter: Design and Performance Analysis in Urban Air Mobility Scenario,” International Journal of Hydrogen Energy, Vol. 50, 2024, pp. 891-907.
  •  
  • 19. Kwon, D.J., Kim, J.H., DeVries, K.L., and Park, J.M., “Optimized Epoxy Foam Interface of CFRP/Epoxy Foam/CFRP Sandwich Composites for Improving Compressive and Impact Properties,” Journal of Materials Research and Technology, Vol. 11, 2024, pp. 62-71.
  •  
  • 20. Kim, J.H., Wang, Z.J., Kwon, K.Eek., Shim, W.S., Yang, S.B., and Kwon, D.J., “Evaluation of Resin Impregnation Using Self-sensing of Carbon Fibers,” Polymer Testing, Vol. 131, 2024, pp. 108331.
  •  
  • 21. Park, J.M., Jang, J.H., Wang, Z.J., Kwon, D.J., and DeVries K.L., “Self-sensing of Carbon Fiber/carbon Nanofiber–epoxy Composites with Two Different Nanofiber Aspect Ratios Investigated by Electrical Resistance and Wettability Measurements,” Composites: Part A, Vol. 41, 2010, pp. 1702-1711.
  •  

This Article

Correspondence to

  • Mantae Kim***, Dong-Jun Kwon *,**

  • * School of Materials Science & Engineering Major in Polymer Engineering, Gyeongsang National University, Jinju, Korea
    ** Department of Materials Engineering and Convergence Technology, Research Institute for Green Energy Convergence Technology Gyeongsang National University, Jinju, Korea
    *** Aerospace Convergence Materials Center, Korea Institute of Ceramic Engineering and Technology, Jinju, Korea

  • E-mail: ginggiscan@kicet.re.kr, djkwon@gnu.ac.kr