Original Article
  • A study on Resin Filling Analysis and Experiment by VAP and VaRTM Processes

  • Dong-Hwan Yoon*, Kyeong-Ho Seo*, Yu-Jung Kwon*, Jin-Ho Choi*†

  • * CMMS, School of Mechanical and Aerospace Engineering, Gyeongsang National University

  • VaRTM과 VAP 공정의 수지 충진실험 및 해석에 관한 연구

  • 윤동환*· 서경호*· 권유정*· 최진호*†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Kwak, S.H., Kim, T.J., Tak, Y.H., Kwon, S.I., Lee, J.H., Kim, S.Y. and Lee, J.C., “A Study on the Atmospheric Pressure Control of the VARTM Process for Increasing the Fiber Volume Fraction and Reducing Void,” Composites Research, Vol. 34, No. 2, 2021, pp. 88-95.
  •  
  • 2. Kim, S.O., Seong, D.G., Um, M.K., and Choi, J.H., “Experimental and Phenomenological Modeling Studies on Variation of Fiber Volume Fraction during Resin Impregnation in VARTM,” Composites Research, Vol. 28, No. 6, 2015, pp. 340-347.
  •  
  • 3. Kang, M.K., Bae, J.H., and Lee, W.I., “Three-Dimensional Numerical Simulation of Mold-Filling and Void Formation During Vacuum-Assisted Resin Transfer Molding,” Composites Research, Vol. 17, No. 3, 2004, pp. 1-7.
  •  
  • 4. Park, D.C., Kim, T.G., Kim, S.H., Shin, D.H., Kim, H.W., and Han, J.W., “Evaluation of Physical and Mechanical Properties based on Liquid Composite Molding,” Composites Research, Vol. 31, No. 6, 2018, pp. 304-310.
  •  
  • 5. Lin, M.Y., Kang, M.K., and Hahn, H.T., “A Finite Element Analysis of Convection Problems in RTM Using Internal Nodes,” Journal of Composites Part A: Applied Science and Manufacturing, Vol. 31, No. 4, 2000, pp. 373-383.
  •  
  • 6. Soares, L.L., Amico, S.C., Isoldi, L.A., and Souza, J.A., “Modeling of the resin Transfer Molding Process Including Viscosity Dependence with Time and Temperature,” Polymer Composites, Vol. 42, No. 6, 2021, pp. 2795-2807.
  •  
  • 7. Kang, M.K., Jung, J.J., and Lee, W.I., “Analysis of Resin Transfer Moulding Process with Controlled Multiple Gates Resin Injection,” Journal of Composites Part A: Applied Science and Manufacturing, Vol. 31, No. 5, 2000, pp. 407-422.
  •  
  • 8. Danisman, M., Tuncol, G., Kaynar, A., and Sozer, M., “Monitoring of Resin Flow in the Resin Transfer Molding (RTM) Process Using Point-voltage Sensors,” Composites Science and Technology, Vol. 67, 2007, pp. 367–379.
  •  
  • 9. Skordos, A.A., and Partridge, I.K., “Dielectric Flow Sensing in Resin Transfer Moulding of Carbon Fibre Reinforced Composites,” Journal of Plastics Rubber and Composites, Vol. 29, No. 8, 2000, pp. 391-394.
  •  
  • 10. Kim, I.Y., Choi, J.H., and Lee, D.G., “A Study on the Performance Test and Manufacture of the Dielectric Sensor for the Cure Monitoring of the High Temperature Composites,” Journal of the Korean Society for Composite Materials, Vol. 14, No. 1, 2001, pp. 30-38.
  •  
  • 11. Yeo, K.J., Lee, S.K., Um, M.K., and Hwang, B.S., “Cure Monitoring of a Composite Matrix by Dielectrometry,” Proceedings of the Korean Society for Composite Materials Conference, 2001, pp. 110-113.
  •  
  • 12. Kim, H.G., and Lee, D.G., “Dielectric Cure Monitoring of Thermosetting Matrix Composites,” Journal of the Korean Society for Nondestructive Testing, Vol. 23, No. 5, 2003, pp. 409-417.
  •  

This Article

Correspondence to

  • Jin-Ho Choi

  • CMMS, School of Mechanical and Aerospace Engineering, Gyeongsang National University

  • E-mail: choi@gnu.ac.kr