Special Issue
  • Low-Temperature Characteristics of Type 4 Composite Pressure Vessel Liner according to Rotational Molding Temperature

  • Hong-Ro Jung*, Ye-Rim Park**, Dong-Hoon Yang*, Soo-Jeong Park**, Yun-Hae Kim*,**†

  • * Major of Materials Engineering, Deptment of Marine Equipment Engineering, Korea Maritime and Ocean University
    ** Department of Ocean Advanced Materials Convergence Engineering, Korea Maritime and Ocean University

  • 타입 4 복합재 압력용기 라이너의 회전 성형 온도에 따른 저온 특성

  • 정홍로* · 박예림** · 양동훈* · 박수정** · 김윤해*,**†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Richards, M.E., “Low-Cost, Low-Weight CNG Cylinder Development,” Omb No. 0704-0188, 2019.
  •  
  • 2. Yoo, G.H., Ju, Y.S., Heo, S.B., Jeon, S.J., Kim, J.L., and Lee, J.H., “Development of the High Pressure Hydrogen Gas Cylinder (Type4) for Fuel Cell Vehicle(Design Qualification Tests),” The Korean Society for New and Renewable Energy, 2007, pp. 193-196.
  •  
  • 3. Han, M.G., Jung, K.C., and Chang, S.H., “Experimental Study on the Structural Integrity of Type IV Hydrogen Pressure Vessels Experienced Impact Loadings,” Composite Research, Vol. 29, No. 2, 2016, pp. 60-65.
  •  
  • 4. Octavie, O.D., Emmanuel, R., Jacques, V., François, F., Jean, G., and Bruno, F., “Molecular and Macromolecular Structure Changes in Polyamide 11 During Thermal Oxidation”, Polymer Degradation and Stability, Vol. 108, 2014, pp. 123-132.
  •  
  • 5. Oliveira, M.J., Cramez, M.C., Garcia, C.B., Kearns, M.P., and Maziers, E., “Effect of the Processing Conditions on the Microstructure and Properties of Rotational Molded Polyamide 11”, Journal of Applied Polymer Science, Vol. 108, 2008, pp. 939-946.
  •  
  • 6. Bharat, I.C., Elizabeth, T., and John, V., “Processing Enhancers for Rotational Molding of Polyethylene,” Polymer Engineering and Science, Vol. 41, No. 10, 2001, p.1731.
  •  
  • 7. Löhner, M., and Drummer, D., “Multi-Layer Rotational Molding of PE-PA Utilizing a Mulitphase Interlayer to Generate Mechanical Adhesion,” Institute of Polymer Technology, Friedrich-Alexander-Universität Erlangen-Nürnberg, Germany, Spe AntecTM Indianapolis 2016.
  •  
  • 8. Ogila, K.O., Shao, M., Yang, W., and Tan, J., “Rotational Molding:A Review of the Models and Materials”, Express Polymer Letters, Vol. 11, No. 10, 2017, pp. 778-798.
  •  
  • 9. Tan, S.B., Hornsby, P.R., McAfee, M.B., Kearns, M.P., and McCourt, M.P., “Internal Cooling in Rotational Molding—A Review,” Polymer Engineering and Science, Vol. 51, No. 9, 2011, pp. 1683-1692.
  •  
  • 10. Crawford, R.J., Nugent, P.J., and Spence, A., “Process Control For Rotational Molding of Plastics,” Queen's Unversity, Belfast, Northem Ireland.
  •  
  • 11. Jung, H.R., “A Study on the Development and Characteristic Evaluation of a High-Functional Liner for Medium and Large-Sized High-Pressure Hydrogen Gas Type 4 using Rotational Processing Mehtod,” Korea Maritime and Ocean University, 2020.
  •  
  • 12. Hwang, T.K., Doh, Y.D., and Kim, H.G., “Size Effect on Tensile Strength of Filament Wound CFRP Composites,” Composite Research, Vol. 24, No. 5, 2011, pp. 1-8.
  •  
  • 13. Kwon, B., Choi, W., Ju, H., Kweon, J.H., and Nam, Y.W., “Effects of Consolidation Processing Parameters on the Surface Morphology and Void Content of Braided Thermoplastic Composite Tubes,” Functional Composites and Structures, Vol. 3, No. 3, 2021, p. 035004.
  •  
  • 14. René, A., Katalee, J., and Christoph, S., “Enthalpy Relaxation of Polyamide 11 of Different Morphology Far Below the Glass Transition Temperature”, Entropy, Vol. 21, No. 10, 2019, p. 984.
  •  

This Article

Correspondence to

  • Yun-Hae Kim

  • * Major of Materials Engineering, Deptment of Marine Equipment Engineering, Korea Maritime and Ocean University
    ** Department of Ocean Advanced Materials Convergence Engineering, Korea Maritime and Ocean University

  • E-mail: yunheak@kmou.ac.kr