Original Article
  • Manufacturing Characteristics of Hemp/Polypropylene Hybrid Roving Yarns and Composites Using Byproducts from Long Hemp Fiber Production
  • Woo Ju Lim*, Jun Bae Park*, Seong Baek Yang**, Il Jun Gwon*, Dong-Jun Kwon**†

  • * DYETEC Research Institute, Andong, Korea
    ** Department of Materials Science and Convergence Technology, Graduate School of Aerospace and Defense Convergence, RIGET, Gyeongsang National University

  • 대마 장섬유 제조 부산물을 활용한 대마/폴리프로필렌 혼섬 로빙사 및 복합재료의 제조 특성 연구
  • 임우주* · 박준배* · 양성백** · 권일준* · 권동준**†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

This study investigated fibrous by-products from hemp long-fiber processing as feedstocks for hemp/polypropylene (PP) blended rovings and composites. At a fixed hemp/PP ratio of 40/60, roving tenacity increased from 4.33 to 13.04 cN/tex as twist increased from 1.7 to 2.6 turns per inch. Among composites containing 0–40% hemp, tensile strength peaked at 32 MPa at 20% hemp, exceeding that of neat PP by 39.1%. At 40% hemp, impact strength, flexural modulus, and heat deflection temperature reached 65 J/m, 4000 MPa, and 150°C, respectively. However, increasing hemp content reduced carding yield and flexural strength, while hemp-containing composites exhibited higher volatile organic compound emissions than neat PP. These findings demonstrate a route for utilizing hemp-processing by-products and provide a basis for balancing material performance and processing yield through process and composition design.


본 연구에서는 국내산 대마의 장섬유 제조 공정에서 발생하는 섬유성 부산물을 활용하여 폴리프로필렌(polypropylene, PP) 혼섬 로빙사와 복합재를 제조하고, 공정 조건 및 대마 함량에 따른 가공성과 물성을 평가하였다. 레팅과 스커칭을 거친 인피섬유의 해클링 과정에서 부산물을 회수하였으며, 대마/PP 배합비를 40/60으로 고정한 로빙사의 꼬임수를 1.7–2.6 TPI로 조절하였다. 또한 대마 함량 0–40%에서 카딩 수율과 복합재의 기계적 특성, VOC 방출 농도 및 열변형온도를 비교하였다. 로빙사의 비강도는 꼬임수 증가에 따라 4.33에서 13.04 cN/tex로 약 3배 증가하여, 꼬임 조절을 통한 인장 성능 개선 가능성을 확인하였다. 복합재의 인장강도는 대마 함량 20%에서 32 MPa로 가장 높았으며, PP 단독 대비 약 39.1% 증가하였다. 충격강도, 굴곡탄성률 및 열변형온도는 대마 함량 증가에 따라 높아져 40%에서 각각 65 J/m, 4000 MPa 및 150°C를 나타내었다. 반면, 대마 함량 증가에 따라 카딩 수율과 굴곡강도는 감소하였으며, 대마 함유 복합재의 VOC 방출 농도는 PP 단독보다 높았다. 본 연구는 대마 장섬유 제조 부산물을 혼섬 로빙사와 PP 복합재로 연결하는 소재화 경로를 제시하였으며, 목표 성능과 가공 수율을 함께 고려한 공정 및 조성 설계의 근거를 제공한다.


Keywords: 대마(Hemp), 섬유성 부산물(Fibrous by-product), 폴리프로필렌(Polypropylene), 혼섬 로빙사(Blended rovings), 복합재료(Composites)

This Article

Correspondence to

  • Dong-Jun Kwon
  • Department of Materials Science and Convergence Technology, Graduate School of Aerospace and Defense Convergence, RIGET, Gyeongsang National University

  • E-mail: rorrir@empas.com, djkwon@gnu.ac.kr