Min-Seong Hwang*, Min-Jung Jun**, Seung-Un Yang***, Byeong-Hun Min*, Jin-Ho Choi*†
* DTCI, School of Mechanical and Aerospace Engineering, Gyeongsang National University
** Hanwha Ocean Co., Ltd.
*** Human Composites Co., Ltd
황민성* · 전민정** · 양승운*** · 민병훈* · 최진호*†
This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
This study investigates the tensile behavior and initial failure characteristics of an L-shaped sandwich composite joint for a rotor sail, reinforced by both bolted fastening and externally bonded laminates. The effects of core geometry and internal reinforcement layup pattern were evaluated through tensile experiments and nonlinear finite element (FE) analysis. Tensile tests were conducted on four joint configurations, and the failure behaviors of the adhesive layer, composite laminates, and face sheet–core interface were numerically investigated. The FE analysis results showed that the initial failure occurred in the adhesive layer between the external reinforcing laminate and the sandwich flange, while no in-plane failure of the composite laminates, interlaminar failure, or interfacial shear failure between the face sheet and core was observed. Among the four configurations, Type 2, incorporating a tapered core and a concentrated internal reinforcement layup, exhibited the highest structural performance, with an initial failure load of 17.43 kN and a maximum load of 33.51 kN. The difference between the FE-predicted failure-initiation loads and the experimental initial failure loads ranged from 2.6% to 7.6%, with an average error of 4.9%, demonstrating the validity of the proposed nonlinear FE analysis. The results also indicate that the core geometry and internal reinforcement layup pattern are key design parameters governing the initial failure and load-carrying capacity of L-shaped sandwich composite joints for rotor sail structures.
본 논문에서는 볼트 체결과 외부 접착 보강이 적용된 로터세일 L형 샌드위치 복합재 조인트를 대상으로 코어 형상과 내부 보강 적층 패턴에 따른 인장거동 및 초기 파손특성을 시험과 비선형 유한요소해석을 통해 평가하였다. 네 가지 형상의 조인트에 대해 인장시험을 수행하고, 접착층, 복합재 적층부 및 면재–코어 계면의 파손거동을 해석적으로 분석하였다. 해석 결과, 최초 파손은 외부 보강 라미네이트와 샌드위치 플랜지 사이의 접착층에서 발생하였으며, 복합재 적층부의 면내파손, 층간파손 및 면재–코어 계면 전단파손은 발생하지 않았음을 확인하였다. 테이퍼형 코어와 집중형 내부 보강 적층을 적용한 Type 2가 초기파손하중 17.43 kN과 최대하중 33.51 kN으로 가장 우수한 성능을 나타냈다. 해석과 시험의 초기파손하중 오차는 2.6–7.6%(평균 4.9%)로 나타나 제안한 비선형 유한요소해석 기법의 예측 타당성을 확인하였다. 또한 코어 형상과 내부 보강 적층 패턴이 로터세일 L형 샌드위치 복합재 조인트의 초기 파손 및 하중지지 성능을 결정하는 주요 설계인자임을 확인하였다.
Keywords: 로터세일(Rotor sail), 샌드위치 복합재(Sandwich composite), L형 조인트(L-shaped joint), 접착층 파손(Adhesive-layer failure), 비선형 유한요소해석(Nonlinear finite element analysis)
This Article2026; 39(5): 525-536
Published on Oct 31, 2026
Correspondence toDTCI, School of Mechanical and Aerospace Engineering, Gyeongsang National University