Original Article
  • 3D-Printed Composite Molds with Toolpath-Based Orthotropy for Predicting Process-Induced Deformation of CFRP Composites
  • Beu-Ni-El Lee*, Jang-Wook Choi**, Eon-Sang Park**, Young-Hoon Jin**, Jea-Hong Kim***,
    Seung-Yeon Shin***, Jin-Ho Choi*†, Hyoung-Jun Lim*†

  • * Aerospace and Defense Convergence, Gyeongsang National University
    ** Body Frame Development Team, Ajin Industrial Co.
    *** Advanced Body Convergence Development Team, HYUNDAI

  • 툴패스 기반 직교이방성을 고려한 3D 프린팅 복합재 금형을 이용한 CFRP 오토클레이브 성형 변형 예측
  • 이브니엘* · 최장욱** · 박언상** · 진영훈** · 김재홍*** · 신승연*** · 최진호*† · 임형준*†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

FDM-based 3D-printed molds have attracted attention as alternatives to conventional metal molds because they reduce manufacturing time and cost. However, toolpath-induced fiber alignment produces thermomechanical orthotropy, which can affect warpage and spring-in in CFRP parts during autoclave curing. In this study, a finite element model was developed by assigning local material orientations to a 3D-printed composite mold according to the actual toolpath, and it was applied to predict curing-induced deformation in flat and Omega-shaped CFRP specimens. For flat CFRP panels fabricated with an S45C metal mold, the prediction errors were 0.08 and 0.08 mm for the 10- and 12-ply cases, respectively. For panels fabricated with the 3D-printed composite mold, the measured average total deformations were 2.24 and 3.03 mm, and the corresponding prediction errors were 0.60 and 0.62 mm, respectively. For Omega-shaped CFRP specimens, the predicted spring-in angles agreed with the measurements within 0.11° for all tested conditions. These results indicate that the proposed toolpath-based orthotropic finite element method can capture curing-induced deformation trends in CFRP parts fabricated using 3D-printed composite molds.


FDM 방식의 3D 프린팅 금형은 제작 기간과 비용을 줄일 수 있어 기존 금속 금형의 대안으로 주목받고 있다. 그러나 툴패스에 따른 섬유 배향은 열-기계적 직교이방성을 유발하며, 오토클레이브 성형 중 CFRP 부품의 warpage 및 spring-in 변형에 영향을 줄 수 있다. 본 연구에서는 실제 툴패스를 따라 3D 프린팅 복합재 금형의 국부 재료 방향을 부여한 유한요소해석 모델을 구축하고, 이를 평판형 및 Omega(Ω) 형상 CFRP 시편의 경화 유도 변형 예측에 적용하였다. S45C 금속 금형으로 제작한 평판형 CFRP 패널의 10 ply 및 12 ply 조건에서 해석 오차는 각각 0.08 mm와 0.08 mm였다. 3D 프린팅 복합재 금형 조건에서 실험 평균 총 변형량은 각각 2.24 mm와 3.03 mm였으며, 해석 오차는 각각 0.60 mm와 0.62 mm였다. Omega(Ω) 형상 CFRP 시편의 spring-in 예측 오차는 모든 조건에서 0.11° 이내였다. 이를 통해 제안한 툴패스 기반 직교이방성 해석 기법이 3D 프린팅 복합재 금형을 이용한 CFRP 성형 변형의 경향을 예측하는 데 적용될 수 있음을 확인하였다.


Keywords: 3D 프린팅 복합재 금형(3D-printed composite mold), 툴패스 기반 직교이방성(Toolpath-based orthotropy), 오토클레이브 성형(Autoclave molding), 유한요소해석(Finite element analysis), 뒤틀림(Warpage)

This Article

Correspondence to

  • Jin-Ho Choi*, Hyoung-Jun Lim*
  • Aerospace and Defense Convergence, Gyeongsang National University

  • E-mail: choi@gnu.ac.kr, hj.lim@gnu.ac.kr