Byeongwoo Im*,**, Duck-Joo Yang***, Soon Hyeok Hong**†, Seo Gyun Kim*†, Bon-Cheol Ku*,****,*****†
* Institute of Advanced Composite Materials, Korea Institute of Science and Technology (KIST), Jeonbuk 55324, Republic of Korea
** Department of Chemistry, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea
*** Department of Chemistry & Biochemistry, The University of Texas at Dallas, Richardson, Texas 75080, USA
**** Department of Mechanical Engineering, The University of Texas at Dallas, Richardson, Texas 75080, USA
***** Department of JBNU-KIST Industry-Academia Convergence Research, Graduate School, Jeonbuk National University, 54896, Republic of Korea
임병우*,** · 양덕주*** · 홍순혁**† · 김서균*† · 구본철*,****,*****†
This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
Polyethylene (PE) is a promising low-cost precursor for carbon fibers because of its high carbon content, low raw-material cost, broad availability, and melt processability. Compared with conventional polyacrylonitrile (PAN) precursors, PE enables melt spinning and can eliminate polymer dissolution, coagulation, washing, drying, and solvent-recovery steps. The major technical challenge is that PE is thermoplastic and therefore requires artificial stabilization before carbonization. This review summarizes PE-based carbon fiber research by integrating the precursor polymer design, melt spinning and drawing, stabilization, carbonization/graphitization, and scale-up from a process–structure–property perspective. In this review, particular emphasis is placed on the trade-off between high molecular orientation/crystallinity, which is favorable for precursor strength and graphitic alignment, and the reduced diffusion of stabilizing agents, which can increase stabilization time. Sulfonation remains the most established stabilization route, whereas electron-beam (EB), ultraviolet (UV), and hybrid approaches are being investigated to reduce stabilization severity and residence time. Recent scale-up work has demonstrated a 10,000-filament PE precursor route and continuous conversion to carbon fibers with tensile strength up to about 2.0 GPa and modulus up to about 170 GPa. These results indicate that PE-based CF research is moving from laboratory material screening toward integrated fiber-processing and industrial-scale manufacturing. Future progress will require simultaneous optimization of molecular architecture, fine/highly oriented melt-spun precursors, rapid and uniform stabilization, tension-controlled carbonization, catalytic graphitization, and multi-filament tow production for low-cost composites.
폴리에틸렌(polyethylene, PE)은 높은 탄소함량, 저렴한 원료가격, 높은 공급 안정성 및 우수한 열가소성 때문에 저가 탄소섬유 전구체로 주목받고 있다. 특히 용융방사가 가능하여 기존 폴리아크릴로니트릴(polyacrylonitrile, PAN) 전구체의 용액방사에서 요구되는 고분자 용해, 응고, 세척, 건조 및 용매 회수 공정을 단순화할 수 있다는 장점이 있다. 반면 PE는 열가소성 고분자이므로 탄화 전에 인공적인 안정화가 필요하며, 안정화 과정이 PE 기반 탄소섬유 제조의 가장 중요한 기술적·경제적 병목으로 평가된다. 본 총설에서는 특히 높은 분자배향과 결정성은 전구체 강도와 탄소층 배향에 유리하지만 안정화제의 확산을 제한하여 안정화 시간을 증가시킬 수 있다는 상충관계에 주목하였다. 설폰화는 현재 가장 확립된 안정화 방법이나, 전자선(EB), 자외선(UV) 및 복합화 기술은 안정화 시간과 화학적 부담을 감소시키기 위한 대안으로 연구되고 있다. 최근에는 10,000-filament PE 전구체 제조와 연속식 전환공정이 보고되었으며, 최대 약 2.0 GPa의 인장강도와 170 GPa의 탄성률을 갖는 PE 기반 탄소섬유가 제조되어 연구의 중심이 실험실 수준에서 산업적 scale-up으로 이동하고 있음을 보여준다. 향후에는 분자구조 설계, 고배향·미세직경 용융방사, 고속·균일 안정화, 장력제어 탄화, 촉매 흑연화 및 multi-filament tow 제조를 통합한 연속공정 개발이 저가 탄소섬유 개발을 위해 필요할 것이다.
Keywords: 폴리에틸렌(Polyethylene), 탄소섬유(Carbon fiber), 전구체(Precursor), 용융방사(Melt spinning), 안정화(Stabilization), 설폰화(Sulfonation), 탄화(Carbonization)
This Article2026; 39(5): 483-490
Published on Oct 31, 2026
Correspondence to* Institute of Advanced Composite Materials, Korea Institute of Science and Technology (KIST), Jeonbuk 55324, Republic of Korea
** Department of Chemistry, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea
**** Department of Mechanical Engineering, The University of Texas at Dallas, Richardson, Texas 75080, USA
***** Department of JBNU-KIST Industry-Academia Convergence Research, Graduate School, Jeonbuk National University, 54896, Republic of Korea