Original Article
  • Design and Characterization of a Conductive-Fabric-Based Flexible Piezoresistive Sensor
  • Seik Park*, Hyeongseok Kang*, Eunji Kim**, Seonggun Joe***†

  • * Department of Aerospace and Mechanical Engineering, Korea Aerospace University
    ** Department of Artificial Intelligence, Korea Aerospace University
    *** Department of Autonomous Systems Engineering, Korea Aerospace University

  • 전도성 패브릭 기반 유연 압저항 센서의 설계 및 특성 평가
  • 박세익* · 강형석* · 김은지** · 조성건***†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

Accurate measurement of human hand motions has been highlighted in robotic systems for recognizing human motion intent and utilizing it for robot control and learning. In this view, wearable sensors capable of reliably measuring finger-joint movements are required. Among various sensing approaches, conductive fabric-based piezoresistive sensors are suitable for multi-channel wearable systems due to their high flexibility and simple signal acquisition circuits. However, repeated loading changes the contact conditions between conductive fibers, resulting in baseline drift and transient output peaks that deteriorate measurement reliability. To address these, this work proposes a pressure-fixed packaging method for photocurable-resin-coated conductive fabric sensors. Herein, the sensing fabric is pre-compressed between two rigid plastic plates, thereby providing a constant initial contact pressure prior to measurement. To validate the effectiveness of the proposed method, four alternative configurations, including ring-type, point-type, zig-zag-patterned, and silicone-inserted sensors, were fabricated and compared with the basic and pressure-fixed packaged sensors under identical repeated-loading conditions. The experimental results demonstrated that pressure-fixed packaging reduced baseline drift and transient output peaks by 40.9% and 47.1%, respectively, compared with the basic sensor. Moreover, the consistency of the output waveforms across repeated loading cycles was improved. In contrast, the alternative configurations based on geometric modification or dissimilar material insertion exhibited positional slippage, electrode damage, or limited suppression of baseline drift. These results demonstrate that structurally stabilizing the initial contact state of the conductive fabric is effective in reducing output instability under repeated loading. Since the proposed method can be implemented solely through structural assembly without changing the sensing material or introducing a complex fabrication process, it can contribute to improving the measurement reliability of conductive fabric-based piezoresistive sensors for wearable hand-motion measurement and other related applications.


로봇 시스템에서 사람의 손동작을 정밀하게 계측하는 기술은 사용자의 동작 의도를 인식하고 이를 로봇의 제어 및 학습에 활용하기 위한 핵심 요소이며, 이를 위해 손가락 관절의 움직임을 안정적으로 측정할 수 있는 착용형 센서가 요구된다. 특히, 전도성 패브릭 기반 압저항 센서는 높은 유연성과 단순한 신호 획득 회로로 인해 다채널 착용형 센서에 적합하지만, 반복 하중에 따른 섬유 간 접촉 상태의 변화로 기준선 드리프트(baseline drift)와 순간적인 출력 피크가 발생하여 계측 신뢰성이 저하될 수 있다. 본 연구에서는 광경화성 레진이 코팅된 전도성 패브릭 센서에서 발생하는 이러한 출력 불안정성을 개선하기 위해, 센싱 패브릭을 두 장의 강성 플라스틱 판 사이에 미리 압축하여 측정 이전부터 일정한 초기 접촉 압력을 부여하는 압력 고정형 패키징 기법을 제안하였다. 제안한 기법의 효과를 검증하기 위해 반지형, 포인트(Point)형, 지그재그(Zig-Zag) 패턴형 및 실리콘 삽입형의 네 가지 대안 구성을 제작하고 기본 센서 및 압력 고정형 패키징 센서와 동일한 반복 하중 조건에서 비교하였다. 실험 결과, 압력 고정형 패키징은 기본 센서 대비 기준선 드리프트를 40.9%, 출력 피크를 47.1% 저감하였으며, 반복 사이클 간 출력 파형의 일관성 또한 향상되었다. 반면 형상 변경이나 이종 재료 삽입에 기반한 비교 구성에서는 위치 이탈, 전극 파손 또는 제한적인 드리프트 저감 효과가 관찰되었다. 이러한 결과는 전도성 패브릭의 초기 접촉 상태를 구조적으로 안정화하는 것이 반복 하중에 따른 출력 불안정성을 저감하는 데 효과적임을 보여준다. 제안한 기법은 별도의 감지 소재 변경이나 복잡한 제작 공정 없이 조립 방식만으로 구현할 수 있어, 착용형 손동작 계측을 포함한 전도성 패브릭 기반 압저항 센서의 계측 신뢰성 향상에 활용될 수 있다.


Keywords: 전도성 패브릭(Conductive fabric), 저항식 센서(Resistive sensor), 압저항(Piezoresistive), 초기 압력 패키징(Preload packaging), 손동작 계측(Hand-motion capture)

This Article

Correspondence to

  • Seonggun Joe
  • Department of Autonomous Systems Engineering, Korea Aerospace University

  • E-mail: sjoe@kau.ac.kr